By
Robert Frederick Lee
Contrary to myth, solid fencing does not provide the best wind
break. The force of the wind on the solid flat surface creates both
pressure on the windward side and pressure differences on the leeward
side, somewhat similar to the way an airfoil works.
To illustrate this, note that snow fences are designed with porosity, allowing some of the wind to work its way through, yet decreasing and deflecting the air flow. As a consequence of the design, snow will tend to accumulate a few feet in front of the fence, as the vortices of wind redirect.
When designing a wood fence as a wind break, stagger the boards 2 inches apart for every six inches of width. The ideal porosity for windbreak fences is 25-33%, and such a gap will give a 25% porosity. This provides a protection that will extend eight to ten times the height of the fence. Another option is to slope the fencing material, if you are intending to use the fence as a shelter for livestock.
For home and farmyard applications, consider building the fence in staggered sections, with each panel offset from adjacent ones by a foot or so. This gapping increases airflow redirection, while also reducing wind load on the panels. Varying the height of the panels also will aid in this redirection. The intent, of course, is not to stop the wind, but to reduce and redirect.
When installing a wind barrier that is intended to act as a snow fence, do not install the fence right at the point where the snow is to be stopped. Rather, set the fence back several yards, at least, so that the snow that is impeded will drop and accumulate prior to the road way or clear area that you require. Remember that, since the wind break (if properly installed) will create a protection area that is eight to ten times the height of the fence, a four-foot fence will provide a dead zone that is up to 40 feet in front of the fence.
Some permanent wind breaks are nothing more than a good tree or brush line. However, solid rows of trees provide less protection than porous rows, so do not plant so that an impenetrable barrier is created. Instead, use staggered plantings, offset against each other.
Although it may seem counterintuitive, mesh fences can provide good wind barriers, as well. Materials such as the mesh seen along the perimeter of golf driving ranges, plastic and resin meshes and even chain link fencing provide a nominal measure of protection. To illustrate the effectiveness of a simple screen, open your house window on a cold, relatively calm winter day, and feel the coolness of the air coming in against the screen. Then stick your hand outside and feel the difference. That screen has partially blocked the transfer of heat due to convection. It works similarly for wind.
Wind breaks, then, are not so much wind barriers as they are wind speed bumps. Holding back the wind, to paraphrase Jim Croce's song about spitting in the wind or tearing the mask off the old Lone Ranger, should not be foolishly attempted!
To illustrate this, note that snow fences are designed with porosity, allowing some of the wind to work its way through, yet decreasing and deflecting the air flow. As a consequence of the design, snow will tend to accumulate a few feet in front of the fence, as the vortices of wind redirect.
When designing a wood fence as a wind break, stagger the boards 2 inches apart for every six inches of width. The ideal porosity for windbreak fences is 25-33%, and such a gap will give a 25% porosity. This provides a protection that will extend eight to ten times the height of the fence. Another option is to slope the fencing material, if you are intending to use the fence as a shelter for livestock.
For home and farmyard applications, consider building the fence in staggered sections, with each panel offset from adjacent ones by a foot or so. This gapping increases airflow redirection, while also reducing wind load on the panels. Varying the height of the panels also will aid in this redirection. The intent, of course, is not to stop the wind, but to reduce and redirect.
When installing a wind barrier that is intended to act as a snow fence, do not install the fence right at the point where the snow is to be stopped. Rather, set the fence back several yards, at least, so that the snow that is impeded will drop and accumulate prior to the road way or clear area that you require. Remember that, since the wind break (if properly installed) will create a protection area that is eight to ten times the height of the fence, a four-foot fence will provide a dead zone that is up to 40 feet in front of the fence.
Some permanent wind breaks are nothing more than a good tree or brush line. However, solid rows of trees provide less protection than porous rows, so do not plant so that an impenetrable barrier is created. Instead, use staggered plantings, offset against each other.
Although it may seem counterintuitive, mesh fences can provide good wind barriers, as well. Materials such as the mesh seen along the perimeter of golf driving ranges, plastic and resin meshes and even chain link fencing provide a nominal measure of protection. To illustrate the effectiveness of a simple screen, open your house window on a cold, relatively calm winter day, and feel the coolness of the air coming in against the screen. Then stick your hand outside and feel the difference. That screen has partially blocked the transfer of heat due to convection. It works similarly for wind.
Wind breaks, then, are not so much wind barriers as they are wind speed bumps. Holding back the wind, to paraphrase Jim Croce's song about spitting in the wind or tearing the mask off the old Lone Ranger, should not be foolishly attempted!
Bob Lee provides regular tips on do-it-yourself projects and home
handyman construction. In addition to his blogs written for Dr Post ( http://drpostfences.blogspot.com ), he writes personal blogs on his experiences with designing, building and living in a yurt ( http://movingtoayurt.blogspot.com ), rural development and on minimal living.
Article Source:
http://EzineArticles.com/?expert=Robert_Frederick_Lee
0 Comment:
Post a Comment